產品中心 Products Center
571430 COLDWASH HD 25 LTR
Product information
UNITOR™ Coldwash HD™ splits after cleaning, releasing the oil phase for reclamation. Powerful degreaser with quick penetration and good emulsifying properties. The emulsifying agents in this product are biological degradable. Does not contain nonyl phenol ethoxylates or other estrogenic compounds. Effective on mineral oils and petroleum based residues. Safe to use on most metal surfaces and painted surfaces. Removes oil contamination from machinery, engine parts and bilges. Soak cleaning of machinery parts. Rapid rinsing, leaves clean and oil-free surfaces.
Features
- Emulsifying agents are biologically degradable
- Does not contain nonyl phenol ethoxylates or other estrogenic compounds
- Effective on mineral oils and petroleum based residues
- Safe to use on most metal surfaces and painted surfaces
- Removes oil contamination from machinery, engine parts and bilges
- Allows soak cleaning of machinery parts
Benefits
- Easy to recover as it splits after cleaning, releasing the oil phase
- Powerful degreaser with quick penetration and good emulsifying properties
- Rapid rinsing, leaves clean and oil-free surfaces
Specification
General
Invent Hazard Material (IMO/EU) classification | C-49 |
---|
Physical properties
Appearance | Clear brown |
---|---|
Density [g/ml] | 0,90 |
Flash Point [°C] | Above 61 oC |
Form | Liquid |
Technical data
Not Compatible | May swell rubber and synthetic rubber. |
---|
Directions for use
This product is excellent for use on soiled surfaces, bilges and machinery parts.
This degreaser must be applied neat with a brush, by hand spray, immersion, soaking etc. The contact, or soaking, time should be between 15 minutes to 2 hours before washing off with hot or cold water. Hot water will improve the result of the cleaning.
Spot cleaning
Spray neat UNITOR™ Coldwash HD™ onto surfaces to be cleaned. The contact time should be at least 30 minutes or up to 2 hours if time allows. Bulkheads/walls can be washed down by use of high pressure cleaning machines. The best result is achieved with hot water between 60--80°C.
Spray method
Spray UNITOR™ Coldwash HD™ neat onto soiled surfaces. The contact time should be between 15--30 minutes, and then wash off with water. To clean stubborn deposits, mechanical agitation such as scrubbing will improve the cleaning.
Soak method
Immerse the parts to be cleaned into a bath of neat UNITOR™ Coldwash HD™ for 30 minutes, and then wash off with water.
Circulation method
Cleaning of equipment such as lube oil heat exchangers, fuel oil preheaters and filters can be accomplished by circulating neat UNITOR™ Coldwash HD™.
產品特性
• 乳化劑是可生物降解的
• 不含壬基酚乙氧基化物或其他雌激素化合物
• 對礦物油和石油殘留物有效
• 可在大多數金屬表麵和塗漆表麵上使用
• 可在大多數金屬表麵和塗漆表麵上使用
• 允許對機器部件進行浸泡清潔
優勢
• 清潔後分解 ,釋放油汙 ,易於恢複
• 強力脫脂劑 ,具有快速滲透和良好的乳化性能
• 快速衝洗 ,保持清潔和無油表麵
清潔後拆分 ,釋放油相進行回收 。強力脫脂劑 ,具有快速滲透和良好的乳化性能 。該產品中的乳化劑是可生物降解的 。不含壬基酚乙氧基化物或其他雌激素化合物 。
對礦物油和石油基殘留物有效 。可在大多數金屬表麵和塗漆表麵上使用 。消除機器 ,發動機部件和艙底的油汙 。浸泡清潔機械部件 。快速衝洗 ,保持清潔和無油表麵 。
Product Number Product name
571430 COLDWASH HD 25 LTR
使用說明
該產品非常適用於汙染表麵 ,艙底和機械部件 。
這種脫脂劑必須用刷子 ,手工噴霧 ,浸泡,浸泡等整潔地塗抹 。接觸或浸泡時間應在15分鍾至2小時之間 ,然後用熱水或冷水衝洗 。熱水將改善清潔效果 。
現場清潔
將整潔的UNITOR™Coldwash HD™噴灑在待清潔的表麵上 。如果時間允許 ,聯係時間應至少為30分鍾或最多2小時 。可以使用高壓清潔機衝洗隔板/牆壁 。使用60-80°C的熱水可獲得最佳效果 。
噴霧法
將UNITOR™Coldwash HD™噴塗在汙染的表麵上 。接觸時間應在15-30分鍾之間 ,然後用水衝洗 。為了清潔頑固的沉積物 ,機械攪拌如擦洗將改善清潔 。
浸泡法
將待清潔的部件浸入潔淨的UNITOR™Coldwash HD™浴中30分鍾 ,然後用水衝洗 。
循環方式
可以通過循環使用UNITOR™Coldwash HD™來清潔潤滑油熱交換器 ,燃油預熱器和過濾器等設備。
版權所有 :江蘇亞美國際貿易有限公司 備案號 :蘇ICP備17042192號-1 網站建設 :